ASTM A276-13A PDF

You are on page 1of 8 Search inside document Standard Specification for Stainless Steel Bars and Shapes1 This standard is issued under the fixed designation A; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense.

Author:Meztimuro Fele
Country:Great Britain
Language:English (Spanish)
Genre:Art
Published (Last):18 March 2018
Pages:235
PDF File Size:6.79 Mb
ePub File Size:17.78 Mb
ISBN:583-7-44028-832-4
Downloads:15323
Price:Free* [*Free Regsitration Required]
Uploader:Gardam



A number in parentheses indicates the year of last reapproval. A superscript epsilon? This standard has been approved for use by agencies of the Department of Defense. It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels.

The free-machining types Note 2 for general corrosion resistance and high-temperature service are covered in a separate speci? NOTE 3—There are standards covering high nickel, chromium, austenitic corrosion, and heat resisting alloy materials. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Referenced Documents 2. Current edition approved May 1, Published June Originally approved in Last previous edition approved in as A — 08a.

DOI: Ordering Information 3. Such requirements may include but are not limited to the following: 3. End use: machined valve parts. Manufacture 4. Carbon Manganese Phosphorus 0.

Cb C H A Maximum, unless range or minimum is indicated. C For some applications, the substitution of Type L for Type , or Type L for Type may be undesirable because of design, fabrication, or service requirements. In such cases, the purchaser should so indicate on the order.

D Nitrogen content is to be reported for this grade. F Nickel plus copper shall be 0. G Product analysis tolerance over the maximum limit for carbon and nitrogen shall be 0. Chemical Composition 5. Mechanical Properties Requirements 6. Magnetic Permeability 7.

General Requirements 8. Failure to comply with the general requirements of Speci? Yield Strength,A min ksi MPa 40 40 Elongation in 2 in. An alternative method of determining yield strength may be used based on a total extension under load of 0.

B For some speci? The use of sub-size test specimens, when necessary, is permissible in accordance with Test Methods and De? C Reduction of area does not apply on? DThe material shall be capable of meeting the required reduction of area where listed, but actual measurement and reporting of the reduction of area are not required unless speci? E Or equivalent Rockwell hardness.

G For shapes having section thickness of 1? Keywords Approved May 1, ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phone , fax , or service astm. Permission rights to photocopy the standard may also be secured from the ASTM website www.

BUDERUS ECOMATIC 4000 SERVICEANLEITUNG PDF

Astm a276 13a

A number in parentheses indicates the year of last reapproval. A superscript epsilon? This standard has been approved for use by agencies of the Department of Defense. It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The free-machining types Note 2 for general corrosion resistance and high-temperature service are covered in a separate speci? NOTE 3—There are standards covering high nickel, chromium, austenitic corrosion, and heat resisting alloy materials.

CAMPEGGI SRL CATALOGO PDF

ASTM A276:13a

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Note 3— Thereare standards covering high nickel, chromium, austenitic corrosion,and heat resisting alloy materials. A number in parentheses indicates the year of last reapproval. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

THE CUDDLE SUTRA PDF

Popular Publishers

.

A MENNYORSZG LTEZIK PDF

ASTM A276-13A PDF

.

Related Articles