HYDRAM PUMP DESIGN PDF

It is meant to lift water from a depth of 2m below the surface with no other external energy source required. Based on the design the volume flow rate in the derived pipe was 4. The overall cost of fabrication of this hydram shows that the pump is relatively cheaper than the existing pumps. Introduction The hydraulic Ram pump or hydram is a complete automatic device that uses the energy in the flowing water such as spring, stream or river to pump part of the water to a height above that of the source.

Author:Bashicage Mautaxe
Country:Mexico
Language:English (Spanish)
Genre:Technology
Published (Last):27 February 2018
Pages:200
PDF File Size:15.74 Mb
ePub File Size:10.78 Mb
ISBN:907-2-46822-651-2
Downloads:55528
Price:Free* [*Free Regsitration Required]
Uploader:Yozshugul



It is meant to lift water from a depth of 2m below the surface with no other external energy source required. Based on the design the volume flow rate in the derived pipe was 4. The overall cost of fabrication of this hydram shows that the pump is relatively cheaper than the existing pumps. Introduction The hydraulic Ram pump or hydram is a complete automatic device that uses the energy in the flowing water such as spring, stream or river to pump part of the water to a height above that of the source.

With a continuous flow of water a hydram operates continuously with no external energy source. A hydram is a structurally simple unit consisting of two moving parts. These are the impulse valve or waste valve and the delivery check valve. The unit also consists of an air chamber and an air valve. The operation of a hydram is intermittent due to the cyclic opening and cloning of the waste and delivery values.

The closure of the waste valve creates a high pressure rise in the drive pipe. An air chamber is required to transform the high intermittent pumped flows into a continuous stream of flow. The air valves allow air into the hydram to replace the air absorbed by the water due to the high pressure and mixing in the air chamber. Pumps are among the oldest of the machines.

Today, pumps are the second most commonly used kind of industrial equipment after the electric motors Working, The first pumps were force pumps and it is interesting that the earliest known example, a pump used by the Greeks in B. C incorporated an air vessel. The use of this device was suspended in the middle-ages and revived in the 16th century when a German translation of the Greek work describing the pump was published.

The earliest pump to be used was the hand pump. More advanced pumps were, however, known to the Romans, as shown by the double cylinder force pump now preserved in the British museum, but their use was apparently lost in this century at the end of the Roman Empire. In Roman times, the first reciprocating pump appeared BC and this remained the main pump type in use for several centuries, operated by hand, animal, water or wind power, mechanical skill developed, and metals came more into use, but the limiting factor with all these older pumps was the relatively low power output which is delivered by them.

The highest power developed by wind miles or water wheel were of the order of 10 horsepower hp. The reciprocating pumps, which relied on suction, could only lift water slightly above 10 metres. The performance of known types of pumps continued to be improved upon and their range of applications extended.

One of such is the peristaltic pump which was developed into a pump for handling slurries of high specific gravity on a cost effective basis. Similarly, the Archimedean screw pump was developed into giant sizes for lifting water to high elevations.

It is reported that the first hydraulic ram pump was built by Whitehurst , which operated manually by the opening and closing of the stopcock. This hydram was able to raise water to a height of 4.

The first automatic hydram was invented by Montgolfier in for raising water in his paper mill. Easton and James were the first to produce hydrams in large scale for commercial purpose. Their rams were used for supplying water to large country houses, farms and village communities. Calvert evaluated the performance characteristics of hydraulic ram. The possible independent variables of hydraulic ram installations were considered and with certain assumptions their number reduced using dimensionless parameters such as the Reynolds number, the Froude number, the Mach number, the head ratio and the coefficient of fluid friction.

The Reynolds numbers was known to be in effective in machines of practical size and that a range exists over which the Mach number has little influence. The Froude number was found to be the criteria for defining the possibility of operation of the ram and the ram output and efficiency are dependent upon the head ratio.

In , Krol [1] established that it was possible to forecast the behaviour of any automatic hydraulic ram, provided the following properties at a given installation have been determined separately. According to Calvert the dimension of the drive pipe has a limiting value. This, he established by applying dimensional analysis technique.

The relevant parameters were the head ratio, friction coefficient and the dimensionless numbers corresponding to those of Froude, Reynolds and Mach. Hydraulic Ram for village use was developed by V. A in USA [2]. The Ram was only used for small water supply with the impulse valve being designed to act on a spring mechanism, while the delivery valve is a simple clack valve. A general description of the hydraulic ram which solved most of the design problems was undertaken by Molyneux [3].

DRYDEN OUTLINES OF CHEMICAL TECHNOLOGY PDF

Hydraulic Ram Pump

Step Howsitdodat? So here goes for the operation of the pump. As the pump cycle begins, water flows down the stand pipe, and up through the swing check valve. Water begins to flow faster and faster around the flapper in the check valve, until friction draws the flapper up, slamming it closed.

LAS SIETE DISPENSACIONES PDF

Hydraulic ram

.

Related Articles